The Effect of adding petroleum resins C9 and C5 on the properties of Qayyarah asphalt

Mhmood Khleel Saleem; Ammar Ahmed Hamdoon; Khalid Ahmed Owaid

doi:10.56286/h64dhy69

Authors

Mhmood Khleel Saleem Department of Chemical and Petroleum Industries, Technical Engineering College, Northern Technical University, 41001 Mosul, Iraq https://orcid.org/0000-0001-5135-9812
Ammar Ahmed Hamdoon Department of Chemistry, College of Education for Pure Science, University of Mosul, 41002 Mosul, Iraq
Khalid Ahmed Owaid Department of Chemistry, College of Education for Pure Science, University of Mosul, 41002 Mosul, Iraq

DOI:

https://doi.org/10.56286/h64dhy69

Keywords:

Asphalt, Rheological properties, Petroleum Resin, Load, Modify Asphalt

Abstract

The effect of petroleum resins on Al-Qayyarah asphalt was studied to modify its chemical, physical, and engineering properties. Due to climate change, rising temperatures, and increased loads, traditional asphalt has become unsuitable for paving main roads, leading to the search for alternatives or modifications to the properties of conventional asphalt. Therefore, petroleum resins of both aliphatic and aromatic types were used due to their rapid mixing compatibility and being solid materials. In addition, bonding materials like sulfur help with the interlocking and stability of asphalt mixing over time bonding petroleum resins with asphalt compounds through free radical reactions. Petroleum resins were used at a rate of up to 5% of the weight of the asphalt. The effect of both types was significant on the properties of the asphalt, as the aromatic resins had a considerable impact achieving a Marshall stability of up to 22KN and indirect tensile strength of 1.985KPa to determine its resistance to heat and moisture. Therefore, the addition of petroleum resins to Al-Qayyarah asphalt significantly improves the performance of the asphalt, provides excellent storage stability with the asphalt, and increases its load-bearing capacity.

Downloads

Download data is not yet available.

References

Hakeem, J., Aman, M. Y., Tawab, M., & Ali, K. (2016). Performance Evaluation of Hot Mix Asphalt Concrete by Using Polymeric Waste Polyethylene. In 1st EAI International Conference on Computer Science and Engineering. European Alliance for Innovation (EAI).?

Tarsi, G., Tataranni, P., & Sangiorgi, C. (2020). The challenges of using reclaimed asphalt pavement for new asphalt mixtures: A review. Materials, 13(18), 4052.?

Abd Taih, S. (2011). The effect of additives in hot asphalt mixtures. Journal of Engineering and Sustainable Development, 15(3), 132-151.?

Elkashef, M., Elwardany, M. D., Liang, Y., Jones, D., Harvey, J., Bolton, N. D., & Planche, J. P. (2020). Effect of using rejuvenators on the chemical, thermal, and rheological properties of asphalt binders. Energy & Fuels, 34(2), 2152-2159.?

Zohuriaan-Mehr, M. J., & Omidian, H. (2000). Petroleum resins: an overview. Journal of Macromolecular Science, Part C: Polymer Reviews, 40(1), 23-49.?

Yan, K., Sun, H., You, L., & Wu, S. (2020). Characteristics of waste tire rubber (WTR) and amorphous poly alpha olefin (APAO) compound modified porous asphalt mixtures. Construction and Building Materials, 253, 119071.?

Nie, X., Li, Z., Yao, H., Hou, T., Zhou, X., & Li, C. (2020). Waste bio-oil as a compatibilizer for high content SBS modified asphalt. Petroleum Science and Technology, 38(4), 316-322.?

Wu, H., Chen, P., Chen, C., & Zhang, W. (2022). Effect of aromatic petroleum resin on microstructure of SBS modified asphalt. Advances in Materials Science and Engineering, 2022(1), 5136748.?

Zhang, W., Qiu, L., Liu, J., Hu, K., Zou, L., Chen, Y., ... & Zang, J. (2021). Modification mechanism of C9 petroleum resin and its influence on SBS modified asphalt. Construction and Building Materials, 306, 124740.?

Hermadi, M., & Pravianto, W. (2019). The effect of resins on rheological and ageing characteristics of bitumen for pavement. In MATEC Web of Conferences (Vol. 258, p. 01004). EDP Sciences.?

Pei, X., Fan, W., & Chen, S. (2020, May). Investigation on the performance of colored asphalt and pavement. In IOP Conference Series: Earth and Environmental Science (Vol. 514, No. 5, p. 052016). IOP Publishing.?

Nie, X., Hou, T., Yao, H., Li, Z., Zhou, X., & Li, C. (2019). Effect of C9 petroleum resins on improvement in compatibility and properties of SBS-modified asphalt. Petroleum Science and Technology, 37(14), 1704-1712.?

Guo, L., Xu, W., Zhang, Y., Ji, W., & Wu, S. (2022). Selecting the best performing modified asphalt based on rheological properties and microscopic analysis of RPP/SBS modified asphalt. Materials, 15(23), 8616.

Zhang, J., & Tan, Y. (2023). Rheology, morphology and phase behavior of SBS/sulfur modified asphalt based on experimental assessment and molecular dynamics. International Journal of Pavement Engineering, 24(2), 2159029.?

Zhang, J., Sakhaeifar, M. S., & Little, D. N. (2022). Characterisation of rheological properties of sulfur-extended asphalt with/without crumb rubber. International Journal of Pavement Engineering, 23(5), 1491-1499.

Kumar, A., Choudhary, R., & Kumar, A. (2023). Storage stability performance of composite modified asphalt with scrap non-tire automotive rubber, waste plastic pyrolytic oil and sulfur. Plos one, 18(4), e0284473.?

Ahmed, S., Hamdoon, A. A., & Abdulla, M. Residues from The Mishraq Sulfur Mine and The Nano_Sulfur Derived from Them as Modifiers for The Mechanical and Thermal Properties of Iraqi Asphalt. Journal of the Turkish Chemical Society Section A: Chemistry, 11(3), 1055-1064.?

Porto, M., Caputo, P., Loise, V., Eskandarsefat, S., Teltayev, B., & Oliviero Rossi, C. (2019). Bitumen and bitumen modification: A review on latest advances. Applied sciences, 9(4), 742.

Zhu, J., Birgisson, B., & Kringos, N. (2014). Polymer modification of bitumen: Advances and challenges. European Polymer Journal, 54, 18-38.?

Das, A. K., & Panda, M. (2017). Investigation on rheological performance of sulphur modified bitumen (SMB) binders. Construction and Building Materials, 149, 724-732.?

D’Melo, D., Raju, S., Bhattacharya, S., & Subramani, S. (2016). Self-assembly of amorphous sulphur in bitumen–sulphur mixtures and its impact on properties. Construction and Building Materials, 126, 976-982.?

ASTM D36/D36M ? 14´1. (2014) Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus.

ASTM D5/D5M – 13.(2013) Standard Test Method for Penetration of Bituminous Materials.

ASTM D113-07. (2008) Standard Test Method for Ductility of Bituminous Materials1.

Dougherty, G., & Hammond, P. D. (1935). The reaction of sulfur with benzene in the presence of aluminum chloride. Journal of the American Chemical Society, 57(1), 117-118.

ASTM D 3515 – 01. (2011) Standard Specification for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures.

ASTM D-6927. (2015) Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures.

ASTM D6931 ? 17. (2017) Standard Test Method for Indirect Tensile (IDT) Strength of Asphalt Mixtures.

ASTM D7173-20. (2020) Standard Practice for Determining the Separation Tendency of Polymer from Polymer Modified Asphalt.